Difference between revisions of "1.3.6.1.4.1.19376.1.3.1.5"
| Line 5: | Line 5: | ||
{{HL7V3|Laboratory Isolate Organizer |1.3.6.1.4.1.19376.1.3.1.5|Trial| | {{HL7V3|Laboratory Isolate Organizer |1.3.6.1.4.1.19376.1.3.1.5|Trial| | ||
| − | Laboratory Organizer, when present, shall be recorded an organizer in an entryRelationship under the Laboratory data processing entry ([[1.3.6.1.4.1.19376.1.3.1]]) as demonstrated in the figure below. | + | Laboratory Organizer, when present, shall be recorded as an organizer in an entryRelationship under the Laboratory data processing entry ([[1.3.6.1.4.1.19376.1.3.1]]) as demonstrated in the figure below. This module is out of the XDS-Lab Specification. This module does not change requirements stated in that specification but is structured as a module to ensure consistent content representation and re-usability. |
| − | |||
| − | This module is out of the XDS-Lab Specification. This module does not change requirements stated in that specification but is structured as a module to ensure consistent content representation and re-usability. | ||
The figure below shows how the information for this element is coded, and further constraints are provided in the following sections. | The figure below shows how the information for this element is coded, and further constraints are provided in the following sections. | ||
| Line 41: | Line 39: | ||
=====<templateId root='1.3.6.1.4.1.19376.1.3.1.5'/>===== | =====<templateId root='1.3.6.1.4.1.19376.1.3.1.5'/>===== | ||
| − | The <templateId> element identifies this <organizer> as the Laboratory Isolate Organizer. The templateId shall | + | The <templateId> element identifies this <organizer> as the Laboratory Isolate Organizer. The templateId shall be recorded as shown above, root='1.3.6.1.4.1.19376.1.3.1.5'. |
=====<statusCode code=" "/>===== | =====<statusCode code=" "/>===== | ||
The status shall be either "completed" or "obsolete". A status of completed is expected. A status of obsolete means the isolation identification has been replaced by a newer identification (following it) in this revision of the report. | The status shall be either "completed" or "obsolete". A status of completed is expected. A status of obsolete means the isolation identification has been replaced by a newer identification (following it) in this revision of the report. | ||
| − | NOTE: | + | NOTE: Lab TF does not address the use of statusCode - needs discussion. |
=====<effectiveTime value=" "/>===== | =====<effectiveTime value=" "/>===== | ||
| − | The isolation's relevant clinical time (ideally specimen collection time) | + | The isolation's relevant clinical time (ideally specimen collection time) MAY be present. |
=====<specimen><specimenRole classCode="ISLT"><specimenPlayingEntity>...</specimen>===== | =====<specimen><specimenRole classCode="ISLT"><specimenPlayingEntity>...</specimen>===== | ||
The specimenRole shall be "ISLT" and the organism shall be coded with at least one unique international vocabulary. | The specimenRole shall be "ISLT" and the organism shall be coded with at least one unique international vocabulary. | ||
Revision as of 13:54, 20 May 2008
Return to: PCC TF-1/PHLAB/XDSLAB Harmonization
Return to: Laboratory Data Processing Entry
Development Only
The PCC Wiki Content is used only for development of IHE PCC Content. The Normative content of the PCC Technical Framework and the current supplements can be found at http://www.ihe.net/Technical_Framework/index.cfm#PCC
Laboratory Isolate Organizer 1.3.6.1.4.1.19376.1.3.1.5
Laboratory Organizer, when present, shall be recorded as an organizer in an entryRelationship under the Laboratory data processing entry (1.3.6.1.4.1.19376.1.3.1) as demonstrated in the figure below. This module is out of the XDS-Lab Specification. This module does not change requirements stated in that specification but is structured as a module to ensure consistent content representation and re-usability.
The figure below shows how the information for this element is coded, and further constraints are provided in the following sections.
Standards
| CRS | HL7 Care Record Summary |
Uses
See Templates using Laboratory Isolate Organizer
Specification
<ClinicalDocument
...
<component typeCode="COMP">
<structuredBody classCode="DOCBODY" moodCode="EVN">
<component typeCode="COMP">
<section classCode="DOCSECT">
...
<entry typeCode="DRIV">
<templateId extension="Lab.Report.Data.Processing.Entry" root="1.3.6.1.4.1.19376.1.3.1"/>
<act classCode="ACT" moodCode="EVN">
...
<entryRelationship typeCode="COMP">
<organizer classCode="CLUSTER" moodCode="EVN">
<templateId root="1.3.6.1.4.1.19376.1.3.1.5"/>
<statusCode code="completed"/>
<effectiveTime value="20071108000000.0000-0500"/>
<specimen>
<specimenRole classCode="ISLT">
<specimenPlayingEntity>
<code code="79153007" codeSystem="2.16.840.1.113883.6.96" codeSystemName="SNOMED-CT"
displayName="Salmonella tennessee 6,7,14;z29;1,2,7">
<translation xsi:type="CE" code="L-17601" codeSystem="2.16.840.1.113883.6.96" codeSystemName="SNOMED"
displayName="Salmonella tennessee 6,7,14;z29;1,2,7"/>
|
<templateId root='1.3.6.1.4.1.19376.1.3.1.5'/>
The <templateId> element identifies this <organizer> as the Laboratory Isolate Organizer. The templateId shall be recorded as shown above, root='1.3.6.1.4.1.19376.1.3.1.5'.
<statusCode code=" "/>
The status shall be either "completed" or "obsolete". A status of completed is expected. A status of obsolete means the isolation identification has been replaced by a newer identification (following it) in this revision of the report.
NOTE: Lab TF does not address the use of statusCode - needs discussion.
<effectiveTime value=" "/>
The isolation's relevant clinical time (ideally specimen collection time) MAY be present.
<specimen><specimenRole classCode="ISLT"><specimenPlayingEntity>...</specimen>
The specimenRole shall be "ISLT" and the organism shall be coded with at least one unique international vocabulary.